Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
- The power supply system
   + The power supply system of the carburettor engine of 1.3 l
   + System of the central injection (SPFI) the petrol engine
   - System of the distributed injection (MPFI) the petrol engine
      The general information and safety measures
      Removal and installation of assemblage of an air cleaner
      Control mean in temperature of soaked up air - the general information
      Removal, installation and adjustment of a cable of an accelerator
      Removal and installation of components of system of injection Simos 2P
      Removal and installation of components of system of injection Magneti-Marelli 1AV
      Removal and installation of assemblage of the fuel pump and the gauge of measurement of the expense of fuel
      Removal and installation of a fuel tank
      Dump of residual pressure in the power supply system
      Removal and installation of the inlet pipeline
      Check of serviceability of functioning and adjustment of system of injection
      Neetilirovannoe fuel - the general information and use rules
   + The power supply system of the diesel engine
   + Systems of decrease in toxicity and release of the fulfilled gases
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment


Removal and installation of components of system of injection Simos 2P

The preventions made in Section the General information and safety measures see.

The scheme of connection of components MPFI Removal and installation of components of system of injection Magneti-Marelli 1AV see in Section.


The throttle case

REMOVAL

 PERFORMANCE ORDER

1. Remove the top covers of the case of a throttle and an air cleaner (see Has undressed Removal and installation of assemblage of an air cleaner).
2. Disconnect a cable of an accelerator from a control lever position throttle заслонки (see Has undressed Removal, installation and adjustment of a cable of an accelerator).
3. Disconnect a negative wire from the battery.

4. Disunite a socket of electroconducting of the module of position throttle заслонки.

5. Disconnect from the throttle case the vacuum hose going from a cover of a head of cylinders, and a hose of a coal adsorber.

6. Turn out four through bolts and remove the case of a throttle from the inlet pipeline. Remove also a lining (at assemblage it is subject to replacement without fail).

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. Pay attention to following moments:

a) do not forget to replace a sealing lining;
b) Through bolts of fastening of the case of a throttle should be tightened with demanded effort;
c) Track quality of all шланговых and electric connections;
d) do not forget to adjust a tension of a cable of an accelerator (see Has undressed Removal, installation and adjustment of a cable of an accelerator).


Injectors of injection and fuel highway


In the presence of suspicions on malfunction of injectors it is not necessary to start their removal at once. At first try to clean injectors by addition in fuel of a special additive (ask in shops automobile химикалиев).

REMOVAL

 PERFORMANCE ORDER

1. Dump pressure in the power supply system (see Has undressed Dump of residual pressure in the power supply system).
2. Disconnect a negative wire from the battery.
3. Remove the top covers of the case of a throttle and an air cleaner (see Has undressed Removal and installation of assemblage of an air cleaner).

4. Preliminary having marked, disconnect electroconducting from injection injectors.

5. Liberate a plait from clamps on the top part of a fuel highway and shift it aside.

6. Disconnect hoses of giving and return of fuel from the end of a fuel highway. Try to remember adjusting position of hoses - submitting it is located more close to the throttle case.

7. Disconnect a vacuum hose from a forward part of a regulator of pressure of fuel.

8. Also disconnect a small hose from a cover of a head of cylinders...

And a hose of a coal adsorber from a clamp in a back part of a fuel highway.

9. Turn out two fixing bolts and accurately remove a fuel highway together with injectors of injection from the inlet pipeline. In avoidance проливания fuel try not to incline a highway. Track, that at extraction of injectors from landing nests in a highway sealing rings remained on the regular places.

10. Injectors can be removed from a highway in an individual order by extraction of metal clamps.

11. Remove the top sealing rings of injectors. Check up a condition of rings.

12. In case of need remove a regulator of pressure of fuel (see more low).
13. By means of a universal tester measure electric resistance of each of injectors. Compare results of measurements to requirements of Specifications.

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. Pay attention to following moments:

a) do not forget to check up a condition of sealing rings of injectors. Defective rings are subject to replacement;
b) Track reliability of landing of metal clamps of fastening of injectors;
c) Track correctness of connection to a highway of hoses of giving and fuel return;
d) Track quality of all шланговых and electric connections;
e) Before to start car operation check up the power supply system on presence of leaks.


Regulator of pressure of fuel

REMOVAL

 PERFORMANCE ORDER

1. Dump pressure in the power supply system (see Has undressed Dump of residual pressure in the power supply system).
2. Disconnect a negative wire from the battery.
3. Remove the top covers of the case of a throttle and an air cleaner (see Has undressed Removal and installation of assemblage of an air cleaner).

4. Disconnect a vacuum hose from a forward part of a regulator of pressure.

5. For gathering of spilt fuel enclose under the block of a regulator rags.

6. Turn out a bolt located under the vacuum union of a regulator.

7. Throw off a washer and remove a fixing plate from a forward part of a regulator.

8. Remove a regulator from the regular place on a fuel highway. Track, that sealing linings have been removed together with a regulator.

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. Pay attention to following moments:

a) the Worn out sealing rings are subject to replacement without fail;
b) Track correctness of gearing of the top part of a fixing plate. Tighten a bolt with demanded effort;
c) Track durability of connection of a vacuum hose.


The module of position throttle заслонки

The module is built in in the case of a throttle and to replacement in an individual order is not subject. In case of occurrence of problems address for the help to experts of car-care centre.

The gauge of temperature/pressure of air soaked up in the inlet pipeline

REMOVAL

 PERFORMANCE ORDER

1. The gauge is established in a back part of the inlet pipeline.
2. Disconnect a negative wire from the battery.
3. Remove the top covers of the case of a throttle and the inlet pipeline (see Has undressed Removal and installation of assemblage of an air cleaner).

4. Disconnect from the gauge electroconducting.

5. Turn out two fixing screws and take the gauge from the nest in the pipeline. Do not forget to remove a lining.

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. The damaged lining is subject to replacement. Track reliability of a tightening of fixture.


The gauge of temperature of a cooling liquid


The gauge of temperature of a cooling liquid of system of injection of fuel is a part of the gauge of a measuring instrument of temperature (CTS).

The oxygen gauge (l-probe)


See Has undressed Removal and l-probe installation.

The gauge of turns and position of a cranked shaft


The engine Electric equipment see the Head.

The detonation gauge


The engine Electric equipment see the Head.

The electronic block of management (ECU)

ECU it is located behind on the left partition of an impellent compartment. The block is protected by a special code and should not act in film without preliminary consultation of representatives of the firm service-centre of company Skoda. Unapproved рассоединение the multicontact I will corrode can result to infringement of serviceability of functioning ECU.


The relay and safety locks of the fuel pump


The relay of the fuel pump and safety locks of system of injection are located in the assembly block established in salon of the car (the Onboard electric equipment see the Head).

The pump relay is on the fifth position among the relay of the working panel of the assembly block. The electric chain of a contour of a food of the pump is protected by a safety lock № 4.

The relay is taken from the nest by simple вытягивания. Relay installation is unequivocal in view of асимметричности nest forms.

The safety lock acts in film also as well as all other safety locks (the Onboard electric equipment see the Head).

It is necessary to notice that removal of the main safety lock of system of injection (№ 1) leads to deleting of the adaptable data from memory ECU, also as it occurs at battery switching-off. Reboot of working parametres demands some time that can lead to infringement of stability of turns of idling within first several minutes after the first start of the engine.