Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   The general information and safety measures
   Removal and installation ступичных assemblages of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Major repairs of racks of a forward suspension bracket
   Removal, major repairs and installation of the bottom levers of a forward suspension bracket
   Replacement of spherical support of the bottom levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, major repairs and installation of racks of a back suspension bracket
   Major repairs of racks of a back suspension bracket
   Removal, major repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross-section stability
   Removal and installation of the back bridge
   Removal and steering wheel installation
   Removal and installation of a steering column
   Major repairs of a steering column
   Removal and installation of assemblage of the lock of ignition/blocking of a wheel
   Removal, major repairs and installation of the steering mechanism
   Replacement of rubber protective covers картера the steering mechanism
   Removal of air stoppers from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the helmsman наcоса
   Removal and installation of external tips of steering draughts
   Removal and installation of steering draught
   Corners of installation of wheels of the car - the general information
+ Body and salon furnish
+ Onboard electric equipment


Replacement of bearings of back naves

Stupichnaja assemblage of a back wheel

1 — the Cover
2 — a bridge Pin
3 — the Brake drum
4 — the Nave
5 — the Bearing
6 — the Epiploon

7 — the Bolt of fastening of a pin to the lever
8 — the Bearing
9 — the Washer
10 — the Nut
11 — Koronchataja a lock washer
12 — Shplint


 PERFORMANCE ORDER

1. Remove a brake drum (the Brake system see the Head).

2. Having hooked a screw-driver with a flat sting, take an epiploon from assemblage of a brake drum - try to remember how it has been established.

3. Take from a drum the internal bearing.

4. Prop up assemblage and beat out from it a holder of the external bearing.

5. Turn a drum and beat out a holder of the internal bearing.

6. Carefully smooth out a landing nest in a drum, completely having removed all traces of a dirt and old greasing. Teases, agnails and roughnesses remove by means of a fine-grained emery paper. Attentively check up a surface on presence of cracks and other signs of deterioration. In case of need make component replacement. Replacement of bearings and an epiploon is made without fail, without dependence from their condition as at dismantle external holders inevitably collapse. Prepare new bearings, an epiploon and special universal greasing.
7. Before installation slightly grease external holders of bearings with pure impellent oil for the purpose of simplification of landing.
8. Reliably having propped up a drum, plant on the place an external holder of the external bearing. Densely begin to knock a holder in a reception nest, having tracked perpendicularity of its landing. In quality оправки take advantage of a piece of a pipe of suitable diameter - оправка should rest exclusively against external edge of a holder.
9. Turn a drum and, operating in the same order, establish in it an external holder of the internal bearing.
10. Make sure of correctness of landing of both external holders, then carefully wipe assemblage.

11. Fill greasing both конусных the roller bearing, also put greasing on their external holders.

12. Plant the internal bearing in the external holder.

13. Fill a new epiploon with sponges inside in a reception nest from the back party of a drum.

14. Plant an epiploon заподлицо with a drum surface, or against the stop in a back part of the last. In case of need the epiploon can be begun to knock in a nest with the help оправки, the pipe of suitable diameter made of a piece. Remember that оправка should rest only against firm external edge of an epiploon.

15. Turn a drum and plant in the external holder external конусный the roller bearing. Establish a gear washer.
16. Fill bearings of a nave greasing and establish into place assemblage of a brake drum (the Brake system see the Head).