Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   The general information and safety measures
   Removal and installation ступичных assemblages of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Major repairs of racks of a forward suspension bracket
   Removal, major repairs and installation of the bottom levers of a forward suspension bracket
   Replacement of spherical support of the bottom levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, major repairs and installation of racks of a back suspension bracket
   Major repairs of racks of a back suspension bracket
   Removal, major repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross-section stability
   Removal and installation of the back bridge
   Removal and steering wheel installation
   Removal and installation of a steering column
   Major repairs of a steering column
   Removal and installation of assemblage of the lock of ignition/blocking of a wheel
   Removal, major repairs and installation of the steering mechanism
   Replacement of rubber protective covers картера the steering mechanism
   Removal of air stoppers from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the helmsman наcоса
   Removal and installation of external tips of steering draughts
   Removal and installation of steering draught
   Corners of installation of wheels of the car - the general information
+ Body and salon furnish
+ Onboard electric equipment


escort érotique

Removal and installation of assemblage of the lock of ignition/blocking of a wheel

Zamkovaja assemblage

At assemblage will be necessary new срезные screws.

REMOVAL

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Execute procedures of paragraphs with 1 on 5 Has undressed Removal and installation of a steering column.
3. Turn out the top bolts of fastening of a steering column (try to remember adjusting positions of remote washers and rubber pillows). Remove a support collar.
4. Turn out the bottom bolts of fastening of a column, remove rubber pillows and remote washers, then slightly lower a column for the purpose of providing of access to lock assemblage.
5. Remembering an order of connection of sockets, disconnect electroconducting from the lock. On the models equipped иммобилизатором, accurately liberate a ring of the gauge from a casing of the lock and take him aside from a steering column.
6. By means of a hammer and approaching выколотки обстучите heads of coupling bolts of fastening of a casing of the lock on perimetre, having weakened bolts so that there was a possibility of their reversing manually. Having turned out bolts, remove a collar and separate assemblage of the lock from a steering column.
7. In case of need the casing замкового the cylinder can be taken from a fixing collar by removal срезного a bolt.

INSTALLATION

 PERFORMANCE ORDER

1. If it is required, establish a casing замкового the cylinder in a fixing collar and screw new срезной a bolt, slightly having tightened last at the given stage.
2. Get замковую assemblage on the regular place on a steering column. Establish a fixing collar and screw new срезные bolts.
3. In stages in regular intervals tighten both bolts. Check up serviceability of functioning of assemblage, then hold on bolts before cutting of their heads.
4. According to the marks put in the course of dismantle connect to the lock electroconducting. At a corresponding complete set latch into place a gauge ring иммобилизатора.
5. Having tracked correctness of installation of remote washers and rubber pillows, plant a steering column on the bottom support. Screw the bottom fixing bolts, then establish a collar of the top support (again track correctness of assemblage of components) and draw its bolts. Make sure of correctness of position of a column, then tighten all fixture with demanded effort.
6. The further assemblage is made in an order, the return to a dismantle order. Pay attention to following moments:

a) Track correctness of a lining of electroconducting and reliability of fastening of plaits in all provided intermediate clamps;
b) the Order of installation of a steering wheel is stated in Section Removal and steering wheel installation;
c) Before installation of the bottom casing of a column make sure available a small backlash between a steering wheel and the top casing. In case of need modify backlash size, having weakened a collar of the holder подрулевых switches.


The ignition switch

REMOVAL

 PERFORMANCE ORDER

1. Remove lock assemblage.
2. Turn out screws without heads and take assemblage of the switch of ignition from a back part of a casing of the lock.

INSTALLATION

 PERFORMANCE ORDER

1. Make sure of correctness of position of the switch and get it in a lock casing. Having made sure of correctness of introduction of the switch in gearing with the lock, definitively plant assemblage in a casing.
2. Clean a carving of fixing screws and slightly grease with its fresh fixing hermetic. Screw screws in замковую assemblage and strongly tighten them.
3. Establish into place lock assemblage.