Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   The general information and safety measures
   Removal and installation ступичных assemblages of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Major repairs of racks of a forward suspension bracket
   Removal, major repairs and installation of the bottom levers of a forward suspension bracket
   Replacement of spherical support of the bottom levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, major repairs and installation of racks of a back suspension bracket
   Major repairs of racks of a back suspension bracket
   Removal, major repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross-section stability
   Removal and installation of the back bridge
   Removal and steering wheel installation
   Removal and installation of a steering column
   Major repairs of a steering column
   Removal and installation of assemblage of the lock of ignition/blocking of a wheel
   Removal, major repairs and installation of the steering mechanism
   Replacement of rubber protective covers картера the steering mechanism
   Removal of air stoppers from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the helmsman наcоса
   Removal and installation of external tips of steering draughts
   Removal and installation of steering draught
   Corners of installation of wheels of the car - the general information
+ Body and salon furnish
+ Onboard electric equipment


Removal and installation of the stabilizer of cross-section stability of a forward suspension bracket

At assemblage the new cylindrical pin of a rod of a choice of transfers is required.

REMOVAL

 PERFORMANCE ORDER

1. Prop up wedges back wheels, firmly cock a lay brake, then поддомкратьте redock of the car and establish it on props. Remove both lobbies of a wheel.

2. On turned to РКПП the end of a rod of a choice of transfers remove a fixing collar, having provided access to a cylindrical pin.

ри assemblage should replace a collar of a standard complete set more convenient screw or worm. Beat out and will throw out an old cylindrical pin - at assemblage it is subject to replacement without fail.

3. Give a nut of an axial bolt of fastening of a rod of a choice of transfers to the basis of control lever rkpp / to the BASIC plate. Take an axial bolt and disconnect a rod from an axis of plugs of switching in a transmission. Remove a rod from the car. From the basis of control lever РКПП take the axial plug ().
4. Turn out a bolt of fastening of a bar of the mechanism of switching to a transmission. Remove washers and a rubber pillow.
5. Remove both racks of a bar of the stabilizer of cross-section stability (see Has undressed Removal and installation of racks of a bar of the stabilizer of cross-section stability of a forward suspension bracket).

6. Turn out bolts of fastening of collars of support of a bar to a stretcher. Remove collars.

7. Take a bar of the stabilizer of cross-section stability from under the car and remove from it rubber plugs of support.
8. Attentively examine stabilizer components on presence of signs of deterioration, ageing of a material or mechanical damages. It is necessary to give special attention to a condition of rubber plugs of support. Defective components replace.

INSTALLATION

 PERFORMANCE ORDER

1. Put on a stabilizer bar rubber plugs of support (the flat parties upwards).
2. Get a bar of the stabilizer of cross-section stability on the regular place on a stretcher. Establish collars of fastening of support, having tracked correctness of their gearing in a back part of a stretcher. Screw fixing bolts.
3. Establish racks of a bar of the stabilizer of cross-section stability (see Has undressed Removal and installation of racks of a bar of the stabilizer of cross-section stability of a forward suspension bracket), then tighten bolts of collars with demanded effort.
4. Clean a carving of bolts of fastening of components of the mechanism of a gear change.
5. Make sure of correctness of landing of rubber plugs and washers, connect a bar of the mechanism of switching to картеру РКПП. Slightly grease a carving of a fixing bolt with hermetic of type Loctite 279 or Three Bond 1305, then screw a bolt and tighten it with demanded effort (the Transmission see the Head).
6. Make sure of correctness of installation of the axial plug (ок) control lever РКПП. Grease the plug () with universal greasing. Establish into place a rod of a choice of transfers, grease with hermetic (the previous paragraph) a nut carving see, then screw last on a bolt and tighten it with demanded effort (see the Head the Transmission). By means of a new cylindrical pin connect a choice rod to РКПП. Fix a pin a collar of screw or worm type.
7. Establish to the place of a wheel, lower the car on the earth and tighten wheel bolts with demanded effort.